SpellmanHV XRB302 Monoblock® Industrial X-Ray Generators

XRB80PN320 Monoblock® Industrial X-Ray Generators

Integrated HV Supply, Filament Supply, X-Ray Tube, Beam Port and Control Electronics
Compact & Lightweight
Can be Mounted in Any Physical Orientation
Standard RS-232 Digital Interface

*Note: All specifications are subject to change without notice. Please consult the English PDF version of this datasheet for the most up-to-date revision.

Data Sheet

Monoblock® Brochure

Relevant FAQs

80kV, 320W X-Ray Source

Spellman’s XRB80PN320 Monoblock® X-Ray source is designed for OEM applications powering its internal X-Ray tube up to 80kV at 320W. Features like small package size and RS-232 digital interface simplify integrating this Monoblock® into your X-Ray system. Standard models are available with fan shaped beam geometry. Proprietary emission control circuitry provides excellent regulation of X-Ray tube current, along with outstanding stability performance.

Typical applications:

X-Ray Scanning: Food Inspection
Fill Level Confirmation
Security Applications

Specifications

^{(Ref. 128091-001 REV. L)}

X-Ray Characteristics:

Tube Type: Glass tube, Tungsten target, Be filter

Focal Spot Options: 0.8mm x 0.8mm (IEC 336)

Beam Filter: 5052 Al, 0.040" (±0.01")

Beam Geometry: Asymmetrical fan 80° x 10° ±2°

Input Voltage:

200-264Vac, 50/60Hz, 4.0A max

X-Ray Tube Voltage:

Nominal X-Ray tube voltage is adjustable between 40kV to 80kV

X-Ray Tube Current:

0.5mA to 4mA over specified tube voltage range

X-Ray Tube Power:

320W maximum continuous

Voltage Regulation:

Line: ±0.05% for a ±10% input line change

Load: ±0.05% for a 0.5mA to 4mA load change

Voltage Accuracy:

Voltage measured across the X-Ray tube is within ±2% of the programmed value

Voltage Risetime:

Ramp time shall be <500ms from 10% to 90% of rated output

Voltage Overshoot:

Within 5% of rated voltage in <10ms

Voltage Ripple:

≤ 1% p-p of rated voltage @ 1kHz

Current Regulation:

Line: ±0.5% @ 50-100% V nominal over specified Line range

Load: ±0.5% @ 50-100% V nominal over specified Load range

Current Accuracy:

Current measured through the X-Ray tube is within ±2% of the programmed value

Current Risetime:

<500ms from 10% to 90% of rated output

Arc Intervention:

4 arcs in 10 seconds = shutdown

Filament Configuration:

Internal high frequency AC filament drive with closed loop filament emission control

Analog Interface:

0 to 10Vdc ground referenced monitoring signals

Digital Interface:

RS-232

Control Software:

A demo GUI for engineering evaluations will be provided for the RS-232 digital interface upon request.

Interlock Signals:

A hardware interlock functions in digital programming modes.

Operating Temperature:

0°C to +40°C

Storage Temperature:

-40°C to +70°C

Humidity:

10% to 90% relative humidity, non-condensing

Cooling:

Heat exchanger w/fan and oil pump

Input Line Connector:

Terminal block, Schurter, Inc. part no. 6100-33

Digital Interface Connector:

9 pin D, female

Analog Monitoring Connector:

10 pin Phoenix Contact 1755503

PIN SIGNAL PARAMETERS

1 Line 200-264Vac Input

2 GND 200-264Vac Input

3 Neutral Neutral

Grounding Point:

8-32 ground stud provided on chassis

Dimensions:

See outline drawing

Weight:

120lbs (54.4kg) maximum

Orientation:

Can be mounted in any orientation.

X-Ray Leakage:

Not to be greater than 0.5mR/hr at 5cm outside the external surface

Regulatory Approvals:

Designed to be compliant to EEC EMC
Directive and EEC Low Voltage Directive with an external filter.

AC INPUT POWERTERMINAL BLOCK

Pin	Signal	Parameters
1	Line	Line
2	Line	Line
3	Line	Line
4	Neutral	Neutral
5	Neutral	Neutral
6	Neutral	Neutral

RS-232 DIGITAL INTERFACE JB16 9 PIN FEMALE D CONNECTOR

Pin	Signal	Parameters
1	N/C	No Connection
2	TX	RS-232 Transmit
3	RX	RS-232 Receive
4	N/C	No Connection
5	SGND	Signal Ground
6	N/C	No Connection
7	N/C	No Connection
8	N/C	No Connection
9	N/C	No Connection

ANALOG MONITORING— JB11 10 PIN PHOENIX CONTACT

Pin	Signal	Parameters
1	X-Ray Enable	+24Vdc = Enable X-Ray 0Vdc/Open = Disable X-Rays
2	RTN	Signal Return
3	N/C	No Connection
4	kV Monitor	0 to 10Vdc = 0 to 100kV, Zout = 10kΩ
5	SGND	Signal Return
6	mA Monitor	0 to 10Vdc = 0 to 5mA, Zout = 10kΩ
7	Fault	Open Collector, High (Open) = No Fault, 35Vdc @10mA max.
8	HV On Lamp, Relay N/O	Relay Normally Open, 50Vdc @ 1A maximum
9	HV On Lamp, Relay Common	Relay Common, 50Vdc @ 1A maximum
10	HV On Lamp, Relay N/C	Relay Normally Closed, 50Vdc @ 1A maximum