SERIE XRV
- Modelos de 160 kV, 225 kV, 320 kV, 350 kV y 450 kV
- Paquete completo de generador de rayos X
- Circuito de entrada de CA con factor de potencia corregido
- Alimentaciones integradas para filamento doble
- Interfaces digitales: USB, Ethernet y RS-232
- Estabilidad y regulación excelentes
- Disponible en acabado negro con pintura de polvo
1.8 - GENERADORES DE RAYOS X INDUSTRIALES DE 6 KW
Las fuentes de alimentación de alto voltaje para rayos X de la serie XRV de Spellman definen el estándar para los generadores de rayos X compactos para inspección de 1.8 kW a 6.0 kW de alto desempeño. Abarcando un voltaje de salida en el rango de los 160 kV a 450 kV en negativo y configuraciones de salida positiva bipolar, prácticamente existe un modelo disponible para casi cualquier requisito de aplicación.
El circuito activo de corrección de factor de potencia reduce los requisitos de corriente de entrada mientras que minimiza la EMI relacionada con la línea. La topología propia de inversor de Spellman permite densidades sin precedentes de eficiencia y potencia. Una sólida sección de alto voltaje encapsulada reduce aún más el tamaño y peso y proporciona una operación confiable y libre de mantenimiento.
El circuito de control del SMT basado en procesamiento digital de señales (DSP) le proporciona la opción de USB, Ethernet y RS-232 además de una interfaz analógica, simplificando la integración a sistemas de OEM. Las dos fuentes reguladas de alimentación de corriente de filamento con salida de CD se controlan mediante sofisticados circuitos de regulación de corriente de emisión para proporcionar corrientes de tubo de rayos X precisas y estables. También se encuentra incorporado dentro de este generador de rayos X compacto y ahorrador de espacio un minucioso circuito de diagnóstico de fallas y la función para detección, extinción y conteo de arcos.
Especificaciones
(Ref. 128060-001 REV. AE)
Typical Applications
Non Destructive TestingX-Ray Scanning
Security Applications
Medical Applications
Options
400Vac ±10% (6kW only)
GUI Control Software for XRV
XRVC (XRV Controller)
Specifications
Input Voltage:
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
180-264Vac, single phase, 47-63 Hertz, active power factor corrected input to ≥0.98
6.0kW models:
208 or 400Vac, ±10%, three phase, 47-63 Hertz, passive power factor corrected
Input Current:
1.8kW, 3.0kW, 4.0kW and 4.5kW models: <30 amps
6.0kW models: <25 amps per phase
Output Voltage:
Accuracy: 0.25%
Stability: ≤ 0.1% per 8 hours, after 1 hour warm up
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
Load:±0.05% of rated output voltage for a full load change
Line: ±0.05% of rated output voltage over specified input voltage range
6.0kW models:
Load:±0.1% of rated output voltage for a full load change
Line: ±0.1% of rated output voltage over specified input voltage range
Output Polarity:
See “model selection” table
Output Current:
See “model selection” table
Ripple:
See “model selection” table
Temperature Coefficient:
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
50ppm/°C
6.0kW models:
±50ppm/°C
Emission Current:
Accuracy: 0.25%
Stability: 100ppm/°C
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
Load: ±0.05% of rated output current for a change from 30% to 100% of rated output voltage
Line: ±0.05% of rated output current over specified input voltage range
6.0kW models:
Load: ±0.1% of rated output current for a change from 30% to 100% of rated output voltage
Line: ±0.1% of rated output current over specified input voltage range
Filament:
Output:
0-6 amps at a compliance of 10Vdc, maximum
Dual Focal Spot:
Small and large, selectable via interface signal
Configuration:
DC filament drive. Closed loop emission control regulates filament setting to provide desired X-Ray tube emission current
Control Interface:
Remote Interface:
Analog, USB, Ethernet and RS-232 are standard
Control Software:
A Windows graphical user interface example is provided.
Environmental
Temperature Range:
Operating: 0°C to +50°C
Storage: -40°C to +85°C
Humidity:
20% to 85% RH, non-condensing
Mains Input Connector:
1.8kW, 3.0kW, 4.0kW and 4.5kW models:
Type 97-3102A-24-11P
6.0kW models:
Type 97-3102A-24-22P
Interface Connectors:
Digital—Ethernet, RS-232 and USB
Analog—25 pin connector
Output Connector:
See “model selection” table
Cooling:
Forced air
Regulatory Approvals:
Compliant to EEC EMC Directive/Compliant to EEC Low Voltage Directive. File E227588. RoHS Compliant.
XRV160/320/350 SPECIFICATIONS
XRV160*1800 | XRV160*3000 | XRV160*4000 | XRV160*6000 | XRV320P&N1800 | XRV320P&N4500 | XRV350P&N4500 | |
---|---|---|---|---|---|---|---|
DC Output Voltage | 5kV to 160kV | 5kV to 160kV | 5kV to 160kV | 5kV to 160kV | 5kV to ±160kV | 5kV to ±160kV | 5kV to ±175kV |
Polarity* | Pos or Neg | Pos or Neg | Pos or Neg | Pos or Neg | Bipolar | Bipolar | Bipolar |
Output Rated Current | 0-30mA | 0-30mA | 0-50mA | 0-50mA | 0-30mA | 0-30mA | 0-30mA |
Output Power | 1.8kW | 3.0kW | 4.0kW | 6.0kW | 1.8kW | 4.5kW | 4.5kW |
Ripple/Noise (p-p) | <0.025% | <0.05% | <0.1% | <0.25% | <0.025% | <0.1% | <0.1% |
Dimensions | 10.09˝ H x 17.16˝ W x 24˝ D (256mm x 436mm x 609mm) | 2 x (10.09˝ H x 17.16˝ W x 24˝ D) (256mm x 436mm x 609mm) | |||||
Weight | 150 lbs. (68kg) | 150 lbs. (68kg) | 150 lbs. (68kg) | 155 lbs. (70.3kg) | 300 lbs. (136 kg) | 300 lbs. (136 kg) | 300 lbs. (136 kg) |
Output Connector | R24 | R24 | R24 | R24 | Two R24 | Two R24 | Two R24 |
XRV225/450 SPECIFICATIONS
XRV225*1800 | XRV225*3000 | XRV225*4000 | XRV225*6000 | XRV450P&N1800 | XRV450P&N4500 | |
---|---|---|---|---|---|---|
DC Output Voltage | 5kV to 225kV | 5kV to 225kV | 5kV to 225kV | 5kV to 225kV | 5kV to ±225kV | 5kV to ±225kV |
Polarity* | Pos or Neg | Pos or Neg | Pos or Neg | Pos or Neg | Bipolar | Bipolar |
Output Rated Current | 0-30mA | 0-30mA | 0-30mA | 0-30mA | 0-30mA | 0-30mA |
Output Power | 1.8kW | 3.0kW | 4.0kW | 6.0kW | 1.8kW | 4.5kW |
Ripple/Noise (p-p) | <0.025% | <0.05% | <0.1% | <0.25% | <0.025% | <0.1% |
Dimensions | 15.90˝ H x 17˝ W x 30.72˝ D (404mm x 432mm x 780mm) | 2 x (15.90˝ H x 17˝ W x 30.72˝ D) (404mm x 432mm x 780mm) | ||||
Weight | 240 lbs. (109kg) | 240 lbs. (109kg) | 240 lbs. (109kg) | 480 lbs. (218 kg) | 480 lbs. (218 kg) | |
Output Connector | R28** | R28** | R28** | Two R28** | Two R28** |
Units are available in positive output polarity without filament, see model selection table for ordering details.
*Specify “P” for positive or “N” for negative polarity.
**Order SHV HV cable flange p/n 407141-024 if using Comet HV cable with R28SL spring loaded plug.
Pin | Signal | Parameters |
---|---|---|
C | HV Output | XRV160 and XRV320—R24 Connector XRV225 and XRV450—R28 Connector |
S | Small Filament Output | 0 to 6 amps @ 10Vdc |
L | Large Filament Output | 0 to 6 amps @ 10Vdc |
J2 ANALOG INTERFACE—25 PIN D CONNECTOR
Pin | Signal | Parameters |
---|---|---|
1 | Power Supply Fault | Low, sum of faults, HVPS detected a fault, open collector, 50V @ 10mA max |
2 | mA Program | 0 to 10V FS Z in = 10M ohms |
3 | kV Program | 0 to 10V FS Z in = 10M ohms |
4 | Filament Limit L/S Ref.* | 0 to 10V FS Z in = 10M ohms |
5 | Filament Preheat L/S Ref.* | 0 to 10V FS Z in = 10M ohms |
6 | kV Monitor | 0 to 10V FS Z out = 4.99k ohms |
7 | mA Monitor | 0 to 10V FS Z out = 4.99k ohms |
8 | Filament Current Monitor* | 0 to 10V FS Z out = 4.99k ohms |
9 | Signal Ground | Ground |
10 | X-Ray Enable | +24Vdc = X-Ray ON, connect to pin 14 with dry contact relay |
11 | Filament ON* | Filament ON status, low, filament is ON open collector 50V, @ 10mA max |
12 | Interlock 1 | Active low, interlock is closed, safe to enable HV |
13 | Interlock 2 | Active low, interlock is closed, safe to enable HV |
14 | +24Vdc | +24Vdc @ 100mA, maximum |
15 | Filament Enable* | Active low, turn filament ON |
16 | Filament Control* | Active low, filament is regulated by ECR (HV must be ON). Not active, the filament is regulated by the preheat reference |
17 | Filament L/S Select | Filament selection large or small, low = small spot is selected |
18 | Filament L/S Confirm | Open collector, 50V @ 10mA max Filament selection confirm, low = small spot is selected |
19 | HVPS RDY | Low = HVPS ready, open collector, 50V @ 10mA max |
20 | X-Ray ON | X-Ray ON status, low = X-Rays are ON open collector, 50V @ 10mA max |
21 | Interlock Status | Low, interlocks are closed, can enable HV open collector, 50V @ 10mA max |
22 | GND | Digital ground |
23 | X-Ray ON Pre-Warn | Pre-warning, low, before X-Ray ON open collector, 50V @ 10mA max |
24 | Reset | Active low, minimum 10mS transition |
25 | Arc fault | Low, arc fault, the HVPS has detected an arc open collector, 50V @ 10mA max |
*Not active on positive models
MODEL SELECTION TABLE
Model | Voltage | Power | Polarity |
---|---|---|---|
XRV160*1800 | 160kV | 1.8kW | Pos or Neg |
XRV160*3000 | 160kV | 3.0kW | Pos or Neg |
XRV160*4000 | 160kV | 4.0kW | Pos or Neg |
XRV160*6000/208V | 160kV | 6.0kW | Pos or Neg |
XRV160*6000/400V | 160kV | 6.0kW | Pos or Neg |
XRV225*1800 | 225kV | 1.8kW | Pos or Neg |
XRV225*3000 | 225kV | 3.0kW | Pos or Neg |
XRV225*4000 | 225kV | 4.0kW | Pos or Neg |
XRV225*6000/208V | 225kV | 6.0kW | Pos or Neg |
XRV225*6000/400V | 225kV | 6.0kW | Pos or Neg |
XRV320P&N1800 | ±160kV | 1.8kW | Bipolar |
XRV320P&N4500 | ±160kV | 4.5kW | Bipolar |
XRV350P&N4500 | ±175kV | 4.5kW | Bipolar |
XRV450P&N1800 | ±225kV | 1.8kW | Bipolar |
XRV450P&N4500 | ±225kV | 4.5kW | Bipolar |
*Specify “P” for positive or “N” for negative polarity. Positive polarity models do not have
integrated filament power supplies. Contact Spellman for custom output voltage/power models.
RS-232 DIGITAL INTERFACE—J3 9 PIN FEMALE D CONNECTOR
Pin | Signal | Parameters |
---|---|---|
1 | N/C | No Connection |
2 | TX out | Receive Data |
3 | RX in | Transmit Data |
4 | N/C | No Connection |
5 | SGND | Ground |
6 | N/C | No Connection |
7 | N/C | No Connection |
8 | N/C | No Connection |
9 | N/C | No Connection |
ETHERNET DIGITAL INTERFACE—J4 8 PIN RJ45 CONNECTOR
Pin | Signal | Parameters |
---|---|---|
1 | VBUS | +5 Vdc |
2 | D- | Data - |
3 | D+ | Data + |
4 | GND | Ground |
JB1 MAIN AND AUXILIARY INPUT POWER—TYPE 97-3102A-24-11P (Single Phase Units)
Pin | Signal | Parameters |
---|---|---|
A | Auxiliary AC Line Power | 180-264Vac |
B | Auxiliary Ground | Ground |
C | Auxiliary AC Neutral | Neutral |
D | Main AC Line Power | 180-264Vac |
E | Main Ground | Ground |
F | Main AC Neutral | Neutral |
JB1 MAIN AC INPUT POWER—TYPE 97-3102A-24-22P (Three Phase Units)
Pin | Signal | Parameters |
---|---|---|
A | Line 1 | 208Vac, ±10%, 50/60Hz @ 25 amps |
B | Line 2 | 208Vac, ±10%, 50/60Hz @ 25 amps |
C | Line 3 | 208Vac, ±10%, 50/60Hz @ 25 amps |
D | GND | Ground |
Note: Use 4 conductor cable or single isolated wires rated no
less that 600Vac, 30 amps (10AWG, minimum)
JB2 AUXILIARY AC INPUT POWER—TYPE 97-3102A-20-3P (Three Phase Units)
Pin | Signal | Parameters |
---|---|---|
A | Line 1 | 208Vac, ±10%, 50/60Hz (source 3 phase L1, L2) |
B | Line 2 | 208Vac, ±10%, 50/60Hz (source 3 phase L1, L2) |
C | GND | Ground |
System Ground: System ground wires (10AWG minimum) to
the ground terminal E1 GND to the power supply using ground
stud M6 X 20MM, with M6 nut.
Tablas y Diagramas
DIMENSIONS: in.[mm]
XRV160
TOP VIEW
FRONT VIEW
REAR VIEW
XRV225
TOP VIEW
FRONT VIEW
REAR VIEW